Jump to main content

YASKAWA AC Drive GA700 High Performance Type Technical Manual

Preface and General Precautions
Receiving
Mechanical Installation
Electrical Installation
Startup Procedure and Test Run
Standards Compliance
Network Communications
Troubleshooting
Periodic Inspection and Maintenance
Disposal
- Section Safety
- Disposal Instructions
  - WEEE Directive
Specifications
Parameter List
Parameter Details

Home
Parameter Details
H: Terminal Function Selection
MFDI Setting Values

A1: Initialization

A2: User Parameters

C1: Accel & Decel Time

C2: S-Curve Characteristics

C3: Slip Compensation

C4: Torque Compensation

C5: Auto Speed Regulator (ASR)

C6: Duty & Carrier Frequency

b1: Operation Mode Selection

b2: DC Injection Braking and Short Circuit Braking

b3: Speed Search

b4: Timer Function

b5: PID control

b6: Dwell Function

b8: Energy Saving

d1: Frequency Reference

d2: Reference Limits

d3: Jump Frequency

d4: Frequency Ref Up/Down & Hold

d6: Field Weakening /Forcing

d7: Offset Frequency

E1: V/f Pattern for Motor 1

E2: Motor Parameters

E3: V/f Pattern for Motor 2

E4: Motor 2 Parameters

E5: PM Motor Settings

E9: Motor Setting

F1: Fault Detection in PG Speed Control

F6, F7: Communication Options

MFDI Setting Values

H2: MFDO

H2 MFDO Parameters

MFDO Setting Values

H3: Analog Inputs

H3: MFAI Parameters

Multi-Function Analog Input Terminal Settings

H4: Analog Outputs

H5: Memobus/Modbus Communication

H6: Pulse Train Input/Output

H7: Virtual MFIO Selection

H1: Digital Inputs

L1: Motor Protection

L2: Power Loss Ride Through

L3: Stall Prevention

L4: Speed Detection

L5: Fault Restart

L6: Torque Detection

L7: Torque Limit

L8: Drive Protection

n1: Hunting Prevention

n2: Auto Freq Regulator (AFR)

n3: High Slip Braking (HSB) and Overexcitation Braking

n5: Feed Forward Control

n6: Online Tuning

n7: EZ Drive

n8: PM Motor Control Tuning

nA: PM Motor Control Tuning

o1: Keypad Display Selection

o2: Keypad Operation

o3: Copy Function

o4: Maintenance Mon Settings

o5: Log Function

T0: Tuning Mode Selection

T1: Induction Motor Auto-Tuning

T2: PM Motor Auto-Tuning

T3: ASR and Inertia Tuning

T4: EZ Tuning

MFDI Setting Values

Selects a function set with H1-01 to H1-42.

0: 3-Wire Sequence
1: LOCAL/REMOTE Selection
2: External Reference 1/2 Selection
3: Multi-Step Speed Reference 1
4: Multi-Step Speed Reference 2
5: Multi-Step Speed Reference 3
6: Jog Reference Selection
7: Accel/Decel Time Selection 1
8: Baseblock Command (N.O.)
9: Baseblock Command (N.C.)
A: Accel/Decel Ramp Hold
B: Overheat Alarm (oH2)
C: Analog Terminal Enable Selection
E: ASR Integral Reset
F: Not Used
10: Up Command
11: Down Command
12: Forward Jog
13: Reverse Jog
14: Fault Reset
15: Fast Stop (N.O.)
16: Motor 2 Selection
17: Fast Stop (N.C.)
18: Timer Function
19: PID Disable
1A: Accel/Decel Time Selection 2
1B: Programming Lockout
1E: Reference Sample Hold
20 to 2F: External Fault
30: PID Integrator Reset
31: PID Integrator Hold
32: Multi-Step Speed Reference 4
34: PID Soft Starter Disable
35: PID Input (Error) Invert
3E: PID Setpoint Selection 1
3F: PID Setpoint Selection 2
40: Forward RUN (2-Wire)
41: Reverse RUN (2-Wire)
42: Run Command (2-Wire Sequence 2)
43: FWD/REV (2-Wire Sequence 2)
44: Add Offset Frequency 1 (d7-01)
45: Add Offset Frequency 2 (d7-02)
46: Add Offset Frequency 3 (d7-03)
47: Node Setup (CANopen)
60: DC Injection Braking Command
61: Speed Search from Fmax
62: Speed Search from Fref
63: Field Weakening
65: KEB Ride-Thru 1 Activate (N.C.)
66: KEB Ride-Thru 1 Activate (N.O.)
67: Communications Test Mode
68: High Slip Braking (HSB) Activate
6A: Drive Enable
75: Up 2 Command
76: Down 2 Command
77: ASR Gain (C5-03) Select
78: Analog TorqueRef Polarity Invert
7A: KEB Ride-Thru 2 Activate (N.C.)
7B: KEB Ride-Thru 2 Activate (N.O.)
7C: Short Circuit Braking (N.O.)
7D: Short Circuit Braking (N.C.)
7E: Reverse Rotation Identifier
90 to 96: DWEZ Digital Inputs 1 to 7
9F: DWEZ Disable
101 to 19F: Inverse Input of 1 to 9F

COPYRIGHT© 2024 YASKAWA INDIA PVT LTD